Description
XB1105-B is a dual image tube night vision system that provides the comfort of use and high quality image. Quasi Gen2+ level image enhancement tube, comparable to the performance of low-light night vision devices. With the help of built-in IR illuminator, it can be used in total darkness. It’s designed to be compact, rugged, lightweight and cost effective with superior night vision performance in its same class. It’s can be widely used for wildlife observation, hunting, boating, camping, etc., and it’s the best value on the market. As a product with higher cost-effectiveness within 2000 USD, the binocular dual tube infrared night vision device not only inherits the traditional military industry’s sturdy and durable characteristics, but also has better workmanship. It has been increasingly recognized and favored by outdoor night observation enthusiasts.
Kit includes
Night Vision Binocular, Color packing box, Protective carrying bag, Instruction manual, Lens cleaning cloth, Warranty card, Desiccant.
Features
- High resolution Gen1+ dual image tube system
- Multi-coated all-glass optics
- Camera adaptability
- Rugged and lightweight
- Built-in computerized proximity sensor
- Built-in IR illuminator
- Powerful 6x magnification
- Weather and fog resistant
- Automatic shut-off system
- Low battery indicator
- Two-Year warranty for normal use
Device operating instructions
1.Insert two 3V CR123A batteries into the battery compartment (3) with the negative(-) terminal being on the top.
2.Activate the device by pushing the “O/I” button (1). Power indicator (2) is lit and be green. NOTE: Please leave the objective lens cover (5) on when you test your night vision device in daylight condition. With a pinhole in the lens cap, it allows a small amount of light to transmit for testing purpose. Night vision can be used without the objective lens cover only in dark conditions.
3.If the object is viewed in a complete darkness, activate the infrared illuminator switch by pressing the “IR” button (7). IR light indicator (9) is lit and be red. A red beam is emitted from IR illuminator (10).
4.There’s the built in computerized proximity sensor for this binocular. Activate it by pressing the “A” button (8). The proximity sensor indicator (11) is lit and be yellow. Turn the device on when in viewing position and off when not. In this case, it helps to use conveniently and also save much sources.
5.Direct night vision at the observed object. Rotate the objective lens (6) and eyepiece (4) until the image is sharp and clear. To focus at the object located at a different distance, it is sufficient to just adjust the objective lens.
Precautions
1.Do not disassemble the unit.
2.It’s better to use device under +5℃ to +40℃. After the unit usage in temperatures below zero, wait at least 3 hours at room temperature, to avoid condensation accumulating on the internal lens surfaces and the consequent fogging caused by extreme temperature differences.
3.Keep the device in soft carrying bag, ventilated and dry place with temperature which does not exceed +15℃. Keep away from heating device and avoid direct sunlight and high humidity which does not exceed 70%.
4.NVD should be used in nighttime and can’t be aim at strong light. If you have to test it during daytime, the front lens cap should never be removed. You can observe the target through the hole in the protection cap.
5.Use good quality lithium battery or alkaline cell, as bad quality batteries will effect the performance of the NVD and easily damage the device.
6.Try to avoid the rain and mist, and avoid dropping, shaking and collision.
7.Use clean soft cloth and dampened in alcohol, if necessary.
8.A useful tip is to remove the battery when the night vision will be not in use for over 3 days to prevent battery leakage and damaging the device.
NOTE: It is normal that the device can not be turned on when the ambient light exceeds 40 Lux. This device has protection system, which cuts off the image intensifier when ambient light level exceeds the limit of 40 Lux during a 10 seconds period. Try not to use it in bright light source for a long time, otherwise it will cause damage to high sensitive optical imaging sensor.
Failture to follow the above precautions may cause the unit damage and will void the manufacturer’s warranty.
